Home > Boat Engine Parts > Hatch Lifter >

LENCO 41"-65" HATCH LIFT (NO SWITCH) 20784-001

List Price: US$450.90
Our Price: US$389.00
You Save US$61.90!

Availability: Usually ships the next business day
Product Code: 29227

Description

The function of the Lenco hatch lift system is simple. Since the hatch lift is based around a ballscrew it is able to push or pull a heavy load and remain at a constant position. To raise a load extend the hatch lift by pressing on the upper part of the switch. To lower a load, retract the hatch lift by pressing the lower part of the switch.

Lenco hatch lifts are easy to install because they install with a single power cable. They draw an average of five amps of power and deliver over 500 pounds of push for heavy engine covers, decks, large hatches and electric consoles. The function of the Lenco hatch lift system is simple. Since the hatch lift is based around a ballscrew it is able to push a heavy load and remain at a constant position. To raise a load extend the hatch lift by pressing on the upper part of the switch.

In case of power failure Lenco hatch lifts are supplied with two clevis pins at the mounting brackets. To pull this pin out while the hatch is closed you must rig it to a point outside of the hatch. To insure easy access under any circumstances, try the Lenco Hatch Lift Slide Bracket. Click on the bracket photo for details

Installation

Operation

Due to the many different variables involved with the numerous applications for Lenco hatch lifts, installation is never the same. Here are some general guidelines that can be of assistance:

The actuator is most powerful when it is installed vertically at 90 degrees
Lifting capabilities decrease the closer the upper or lower mount is located to the hinge
The further from a vertical position the less lifting capability. When retracted, Do Not position hatch lift at an angle less than 30 degrees
Dual actuator systems are recommended for hatches over 500 pounds
Lenco hatch lifts are designed around a ball screw that spins freely when hatch is fully open or closed
For installation, it is important that the hatch lift is able to disengage itself at the fully retracted position.
The ram must be allowed to free spin at both ends of its stroke or it will continue to push or pull against any resistance potentially damaging the hatch lift ot the hatch itself.
Failure to make accurate measure could cause damage to hatch lift or the hatch itself
Lenco hatch lifts are fully submersible and will not drift.
Lenco hatch lifts are offered in both 12 and 24 volts

The function of the Lenco hatch lift system is simple. Since the hatch lift is based around a ballscrew it is able to push or pull a heavy load and remain at a constant position. To raise a load extend the hatch lift by pressing on the part of the switch that says "up". To lower a load, retract the hatch lift by pressing the "down" side of the switch.

It case of power failure Lenco hatch lifts are supplied with two clevis pins at the mounting brackets. To pull this pin out while the hatch is closed you must rig it to a point outside of the hatch.

Mounting Instructions

1. Following the chart above to figure out load on the hatch lift maximum load is 750 lbs. (340.19 kg.)
Y = Total length of hatch
X = Length from the hinge to the hatch lift mounting point
W = Weight of the hatch to be lifted

2. Determine the angle of the hatch lift mount. Do not exceed 45 degrees from center.

3. Mount the hatch lift on the desired location as per the above instructions. IMPORTNAT: It may be necessary to shim the upper or lower mounting bracket up or down so the hatch does not bind when fully closed. The hatch lift does not stop pulling until it has reached its fully closed position. If the hatch fully closes before the hatch lift is fully retracted it will cause damage to the lift or the mounting hardware. Shim the hatch lift with stainless washers for small amounts of length. Use Lenco part #118s for lengths greater then 1/8 inch (3mm).

4. Wire to switch according to the hatch lift wiring diagram in the owners manual supplied with the hatch lift.

Hatch Lifts Size & Fit Chart S = Short, all part numbers ending in S have the same stroke but in a 4� (10.16 cm) shorter length.
Part No.	L.O.A. Retracted Inches (cm)	Approx. Stroke Inches (cm)	L.O.A. Extended Inches (cm)
HL-400	15" (38.10)	4" (10.16)	19" (48.26)
HL-800S	21" (53.34)	8" (20.32)	29" (73.66)
HL-800	25" (63.50)	8" (20.32)	33" (83.82)
HL-1200S	25" (63.50)	12" (30.48)	37" (93.98)
HL-1200	29" (73.66)	12" (30.48)	41" (104.30)
HL-1600S	29" (73.66)	16" (40.64)	45" (114.30)
HL-1600	33" (83.82)	16" (40.64)	49" (124.46)
HL-2000S	33" (83.82)	20" (50.80)	53" (134.62)
HL-2000	37" (93.98)	20" (50.80)	57" (144.78)
HL-2400S	37" (93.98)	24" (60.96)	61" (154.94)
HL-2400	41" (104.14)	24" (60.96)	65" (165.10)
HL-2600	47" (119.38)	26" (66.04)	73" (185.42)
HL-3000	47" (119.38)	30" (76.20)	77" (195.58)