Home > Steering & Engine Control > Boat Hydraulic Steering System > Hydraulic Steering Hose >

Seastar Hose Kit HO51XX Series For HK6400
Seastar Hose Kit HO51XX Series For HK6400


 
Brand New with Factory's Warranty
List Price: US$151.00
Our Price: US$149.00
You save US$2.00!




Availability:: Usually ships the next business day
Product Code: TEL-HS51XX

Hose Length

10' [Add US$10.00]
12' [Add US$10.00]
14' [Add US$14.00]
16' [Add US$20.00]
18' [Add US$40.00]
20' [Add US$50.00]
22' [Add US$60.00]
24' [Add US$100.00]
26' [Add US$90.00]
28' [Add US$100.00]
30' [Add US$116.00]
4'
6'
8'
2'

Description Extended Information
 

SeaStar Outboard hoses are available in kit's (includes two hoses) ranging in length from 2' - 30'. Hydraulic Hose must be protected from chaffing and any possible contact or interference with assembly screws or sharp edges of any type.

The Hydraulic hoses should be secured along the routing path wherever possible and should not be allowed to hang free in any area where they could become a safety hazard. Teleflex recommends the use of a rigging tube, PVC piping or conduit for the safe secure installation of hydraulic hoses. Do not install hoses in such a way that they may become exposed to high heat areas such as engine components (i.e.; manifold or exhaust components) or highly corrosive areas such as battery fumes or electrical connections.

Continuous kinking, chaffing, rubbing or twisting may eventually weaken hose(s) to a point where it could rupture from normal steering pressure causing loss of steering, resulting in personal or property damage. Visually inspect all hoses and fittings for wear and or damage as part of your regular annual maintenance. Replace any hose or components suspect of excessive wear.

Outboard hoses are supplied with pre-attached hose fittings on both ends.

How to Measure Hydraulic Hoses

New Installation:

Measure hose routing path from wheel center line to engine connection, as follows:

A = Center line of wheel to gunwale (or deck, if routed downward),
B = Dash to transom,
C = Gunwale to centerline of cable connection at centered tiller.

Most cylinders move with the engine/rudder; enough slack must be left in hoses/tubing to prevent sharp bends (less than 3” radius) and/or kinking.

Where rigid tubing is used, flexible hoses must be installed between tubing and cylinder, to allow cylinder articulation.

For Most Cylinders, add A, B & C + 24”, round up to next even foot. Order that length hose kit, or twice that length in tubing.

Hose routings (such as those found on pontoon boats) may vary from this drawing. Confirm length by laying a garden hose along cable path and measure run from wheel to engine connection point.

Typical Single Station Routing

A single, front-mount outboard cylinder system is shown in this diagram.

If your hydraulic system is different than the one depicted and/or you have any questions about hydraulic steering after reviewing this guide, please contact SeaStar Solutions® Technical Service.

SEASTAR Outboard Hose Kit (HO51_ _*)
Includes two hoses – can be used with all SeaStar systems, except SeaStar PRO, BayStar, Capilano and 3-line inboard systems.

Note: The price is subject to change at any time without any notice. Not responsible for any typographical errors. Any products can be cancelled from sale at any time.
  • All products sold here come with Full Manufacturer's Warranty
  • Email us at
  • [email protected] for any quesitons
  • WarningWARNING: This product can expose you to chemicals including Di-n-hexyl Phthalate, DnHP, which is known to the State of California to cause reproductive harm, and Vinyl Chloride which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Be the first to write a review for this product

Browse for more products in the same category as this item:

Steering & Engine Control > Boat Hydraulic Steering System > Hydraulic Steering Hose
Engine Parts > Boat Steering System > Boat Hydraulic Steering > Hydraulic Steering Hose