Applications
• General purpose system
• Single and multiple engine capability
• Total power to 700 HP
• Typical applications include center console fishboats and cruisers

Features
• Independent engine tilt for twin engine installations
• Easy steering
• 5 turns lock to lock steering response

Product Datasheet

HOW TO SELECT A FRONT MOUNT OUTBOARD STEERING SYSTEM

1. From the order guide below select the system configuration based on:
a) the number of engines, and
b) the total engine power to be installed.
2. From the application guide below confirm that the Front Mount Cylinder will fit your specific make, model, and year of engine. Select the adapter kit for single engines or the tie bar kit for dual engines.
3. From the order guide select the appropriate helms and accessory hardware for each steering station.
4. From the order guide select the fitting and hose kits required for the installation. Note: for hoses add the distance required, in feet to the last two digits of the part number.
5. Confirm that there is sufficient space available in the splashwell and dash areas for the steering components. See WARNING.

Notes
Not recommended for use in installations where:
a) chopper, cleaver or surface piercing propellers are used,
b) the engine is highly elevated on the transom,
c) engine trim tabs have been removed,
d) the boat speed exceeds 75 mph (120 km/h), or
e) the power exceeds maximum Coast Guard or M.O.T. recommendations for the boat.

WARNING.
Operational interference of the steering cylinder/cylinder fittings and jackplates/transom/splashwell can occur under certain conditions. Check installation thoroughly throughout the full range of Motor Tilt, Jack Height and Trim before making final installation.

With the introduction of heavier, higher horsepower engines producing more torque, Teleflex Marine has updated its recommendations across various applications (single and multiple engines, different hull types, etc.) Please read carefully to ensure that your current steering system provides the best comfort versus performance available.

Notes
1. Teleflex has specific steering equipment for boats that are driven aggressively, used in severe conditions or with more than 300 HP per engine.
2. ALL ENGINES over 300 HP and all boats that are driven aggressively must use a high strength tiller bolt, kit part #HA5822. All front mount cylinders built after June 15, 2007 will have this high strength bolt included in the box.High strength tiller bolts can be identified by the marking ‘TFX – ARP’ on the head of the bolt (refer to NOTICE below).
3. HC63xx PRO Cylinders are designed for all those critical high speed, single outboard engine boats, such as Bass, Flats combo Race/Ski and other performance orientated boats capable of speeds in excess of 65 mph. For optimal performance, the use of SeaStar PRO Kevlar Steering Hoses is recommended.
4. HC67xx Tournament cylinders are designed for use with high powered fishing/sport boats. If your application calls for dual or triple outboard engines, is capable of speeds exceeding 55 mp/h and runs ion open water, tournament Cylinders should be used.

APPLICATION GUIDE – Single Engine Applications

If your engine’s Horsepower rating is 300+, please refer to our 300HP + Outboard Installation Recommendations prior to selecting a cylinder from this application guide to ensure that you are selecting the correct cylinder for your engine/boat.

Notes:
1. Requires spacer kit HO5090.
2. May require extensive cowling modifications.
3. MUST use High Strength Tiller bolt, part # HA5822. Refer to the Notice on this page identifying the high strength bolt.
4. Optional cylinder part # HC5358. Slight interference may occur when using the HC5358, with the engine in the full tilt position.
5. Cylinder part # HC5358 may also be used in these single engine applications, please see note #4 for interference concerns.

Notice

High Strength Tiller bolt, part# HA5822. ALL cylinders shipped after June 1st, 2007 will have this bolt included in the cylinder package.

Notice
Front Mount Cylinder part# HC5345 is included in the SeaStar Outboard Steering Kits HK6400/63XX and HK7400/73XX. If your engine requires the use of a cylinder other than the HC5345 (see application guides on this page through 3-6) you will need to purchase the individual components (helm, cylinder, hoses, etc.) separately.

Caution
SeaStar Solutions® recommends the use of SeaStar PRO (1500 psi) Kevlar steering hoses with SeaStar PRO Helms.

back to top……………………………………………………………………………………………………………………………….

APPLICATION GUIDE – Twin Engine Applications

If your engine’s Horsepower rating is 300+, please refer to our 300HP + Outboard Installation Recommendations prior to selecting a cylinder from this application guide to ensure that you are selecting the correct cylinder for your engine/boat.

Notes:
1. HC5345 is optional for SINGLE ENGINE ONLY applications. DO NOT use HC5345 for Twin engine applications as operational interference may occur.
2. Requires kit HO5090.
3. Minimum engine center = 27″.
4. May require extensive cowling modifications.
5. HO5030 and HO5064 comes without tie-bar.
6. One cylinder per engine. Must use Mercury supplied tiller bolt for installation.
7. Interference will occur when using a single HC5345 cylinder and HO6003 tiebar when installed in the aft hole on the steering arm.
Options include:
+++a) install tiebar into most forward hole (this will limit steering articulation),
+++b) purchase K-6 Cylinder, and tiebar kit part # HO5009. There will no be no interference when using twin HC5345 cylinders.